Blog Image

Auto Diagnostics

Volvo models supported by icarsoft i906

Volvo Posted on 2015-01-26 16:13:33

Here is the video with Volvo models supported by icarsoft i906. More icarsoft models videos are coming. Subscribe to our youtube channel to get informed when new videos are uploaded.



SAAB models supported by icarsoft i906

Volvo Posted on 2015-01-23 14:20:19

Here is the video with Saab models supported by icarsoft i906. More icarsoft models videos are coming. Subscribe to our youtube channel to get informed when new videos are uploaded.




iCarsoft Volvo/SAAB Multi-system ScanTool i906 presentation

Volvo Posted on 2015-01-19 13:55:09

Here is the iCarsoft Volvo/SAAB Multi-system Scan Tool i906 presentation.
To see details of the supported volvo and saab models watch our next i906 video.
Subscribe to our youtube canal to get informed when new videos are uploaded.




HOWTO: Read and Reset VOLVO Flash Codes

Volvo Posted on 2015-01-05 16:09:29

To retrieve DTCs stored in the ECM memory:

*Switch on ignition to position II, do not start the engine.

The DTCs are displayed by brief operation (1 second) of the test button.

If the LED responds by displaying the flashing code 1-1-1, no faults have been detected.

If a fault is present, the LED will display the appropriate DTC as listed in the DTC tables. Note this is very slow.

Further DTCs can be retrieved by repeating the above until the first DTC is displayed again.

Erasing DTCs

DTCs can be erased only when they have all been displayed and the first DTC has been repeated at least once. The procedure is as follows:

*Switch on ignition to position II.

Note! DTCs must be erased with the engine switched off, otherwise the function cannot be guaranteed.

*Press test button and hold for more than five seconds.

*Await LED response.

*Before the LED goes out, press the button again and hold for more than five seconds.

*Switch ignition off and on.

*Start engine.

All DTCs will now be erased and all adaptive values reset.

On ’96/’97 850/900 cars with the 16 way ‘OBDII’ socket, some of the control modules use ‘flash’ codes,

THE USE OF THE FOLLOWING INFORMATION IS ENTIRELY AT THE USERS RISK

To retrieve the flash codes the following procedure can be adopted:

Connect an LED, with the correct polarity, in series with a 1800 ohm resistor, between pin 16 (+) and pin X, where X is the pin corresponding with the module to be read. Connect a push to make switch between pin X and pins 4 or 5 (-).

The circuit can then be used in the same way as the pre ’96 diagnostic sockets, situated in the engine compartment.

For

Motronic 4.3 or Fenix 5.2, X = 3.

850 ECC , X = 6, Timer Type 4, X = 9.

Cruise Control, X = 13.

900 & S/V 90: ABS, X = 12, EZ116K, X = 1, LH 2.4, X = 3.



Volvo V70/S60 DVD spelare

Volvo Posted on 2014-04-14 15:39:15

Nu kan vi förmedla Volvo V70/S60 DVD spelare för 4196 kr + frakt

http://www.orebrobildiagnos.se/OBD2/index.php?main_page=product_info&cPath=3_750_769&products_id=916



INSTALL VOLVO VIDA 2013A VIDA VOLVO SOFTWARE GUIDE

Volvo Posted on 2014-04-08 20:05:42

En bra hemsida om VIDA DICE installation.

http://www.obd2repair.com/news/install-volvo-vida-2013a-vida-volvo-software-guide-a-396.html



Volvo icarsoft i906

Volvo Posted on 2014-03-01 22:37:22

‪Volvo i906 iCarsoft Vehicle Coverage Multi System Diagnostic Tool‬ VIDEO